Signal jammer camera for sale , gps signal jammer for sale ad

By Kyle Wesson, Daniel Shepard, and Todd Humphreys Disruption created by intentional generation of fake GPS signals could have serious economic consequences. This article discusses how typical civil GPS receivers respond to an advanced civil GPS spoofing attack, and four techniques to counter such attacks: spread-spectrum security codes, navigation message authentication, dual-receiver correlation of military signals, and vestigial signal defense. Unfortunately, any kind of anti-spoofing, however necessary, is a tough sell. GPS spoofing has become a hot topic. At the 2011 Institute of Navigation (ION) GNSS conference, 18 papers discussed spoofing, compared with the same number over the past decade. ION-GNSS also featured its first panel session on anti-spoofing, called “Improving Security of GNSS Receivers,” which offered six security experts a forum to debate the most promising anti-spoofing technologies. The spoofing threat has also drawn renewed U.S. government scrutiny since the initial findings of the 2001 Volpe Report. In November 2010, the U.S. Position Navigation and Timing National Executive Committee requested that the U.S. Department of Homeland Security (DHS) conduct a comprehensive risk assessment on the use of civil GPS. In February 2011, the DHS Homeland Infrastructure Threat and Risk Analysis Center began its investigation in conjunction with subject-matter experts in academia, finance, power, and telecommunications, among others. Their findings will be summarized in two forthcoming reports, one on the spoofing and jamming threat and the other on possible mitigation techniques. The reports are anticipated to show that GPS disruption due to spoofing or jamming could have serious economic consequences. Effective techniques exist to defend receivers against spoofing attacks. This article summarizes state-of-the-art anti-spoofing techniques and suggests a path forward to equip civil GPS receivers with these defenses. We start with an analysis of a typical civil GPS receiver’s response to our laboratory’s powerful spoofing device. This will illustrate the range of freedom a spoofer has when commandeering a victim receiver’s tracking loops. We will then provide an overview of promising cryptographic and non-cryptographic anti-spoofing techniques and highlight the obstacles that impede their widespread adoption. The Spoofing Threat Spoofing is the transmission of matched-GPS-signal-structure interference in an attempt to commandeer the tracking loops of a victim receiver and thereby manipulate the receiver’s timing or navigation solution. A spoofer can transmit its counterfeit signals from a stand-off distance of several hundred meters or it can be co-located with its victim. Spoofing attacks can be classified as simple, intermediate, or sophisticated in terms of their effectiveness and subtlety. In 2003, the Vulnerability Assessment Team at Argonne National Laboratory carried off a successful simple attack in which they programmed a GPS signal simulator to broadcast high-powered counterfeit GPS signals toward a victim receiver. Although such a simple attack is easy to mount, the equipment is expensive, and the attack is readily detected because the counterfeit signals are not synchronized to their authentic counterparts. In an intermediate spoofing attack, a spoofer synchronizes its counterfeit signals with the authentic GPS signals so they are code-phase-aligned at the target receiver. This method requires a spoofer to determine the position and velocity of the victim receiver, but it affords the spoofer a serious advantage: the attack is difficult to detect and mitigate. The sophisticated attack involves a network of coordinated intermediate-type spoofers that replicate not only the content and mutual alignment of visible GPS signals but also their spatial distribution, thus fooling even multi-antenna spoofing defenses. Table 1. Comparison of anti-spoofing techniques discussed in this article. Lab Attack. So far, no open literature has reported development or research into the sophisticated attack. This is likely because of the success of the intermediate-type attack: to date, no civil GPS receiver tested in our laboratory has fended off an intermediate-type spoofing attack. The spoofing attacks, which are always conducted via coaxial cable or in radio-frequency test enclosures, are performed with our laboratory’s receiver-spoofer, an advanced version of the one introduced at the 2008 ION-GNSS conference (see “Assessing the Spoofing Threat,” GPS World, January 2009). To commence the attack, the spoofer transmits its counterfeit signals in code-phase alignment with the authentic signals but at power level below the noise floor. The spoofer then increases the power of the spoofed signals so that they are slightly greater than the power of the authentic signals. At this point, the spoofer has taken control of the victim receiver’s tracking loops and can slowly lead the spoofed signals away from the authentic signals, carrying the receiver’s tracking loops with it. Once the spoofed signals have moved more than 600 meters in position or 2 microseconds in time away from the authentic signals, the receiver can be considered completely owned by the spoofer. Spoofing testbed at the University of Texas Radionavigation Laboratory, an advanced and powerful suite for anti-spoofing research. On the right are several of the civil GPS receivers tested and the radio-frequency test enclosure, and on the left are the phasor measurement unit and the civil GPS spoofer. Although our spoofer fooled all of the receivers tested in our laboratory, there are significant differences between receivers’ dynamic responses to spoofing attacks. It is important to understand the types of dynamics that a spoofer can induce in a target receiver to gain insight into the actual dangers that a spoofing attack poses rather than rely on unrealistic assumptions or models of a spoofing attack. For example, a recent paper on time-stamp manipulation of the U.S. power grid assumed that there was no limit to the rate of change that a spoofer could impose on a victim receiver’s position and timing solution, which led to unrealistic conclusions. Experiments performed in our laboratory sought to answer three specific questions regarding spoofer-induced dynamics: How quickly can a timing or position bias be introduced? What kinds of oscillations can a spoofer cause in a receiver’s position and timing? How different are receiver responses to spoofing? These questions were answered by determining the maximum spoofer-induced pseudorange acceleration that can be used to reach a certain final velocity when starting from a velocity of zero, without raising any alarms or causing the target receiver to lose satellite lock. The curve in the velocity-acceleration plane created by connecting these points defines the upper bound of a region within which the spoofer can safely manipulate the target receiver. These data points can be obtained empirically and fit to an exponential curve. Alarms on the receiver may cause some deviations from this curve depending on the particular receiver. Figure 1 shows an example of the velocity-acceleration curve for a high-quality handheld receiver, whose position and timing solution can be manipulated quite aggressively during a spoofing attack. These results suggest that the receiver’s robustness — its ability to provide navigation and timing solutions despite extreme signal dynamics — is actually a liability in regard to spoofing. The receiver’s ability to track high accelerations and velocities allows a spoofer to aggressively manipulate its navigation solution. Figure 1. Theoretical and experimental test results for a high-quality handheld receiver’s dynamic response to a spoofing attack. Although not shown here, the maximum attainable velocity is around 1,300 meters/second. The relative ease with which a spoofer can manipulate some GPS receivers suggests that GPS-dependent infrastructure is vulnerable. For example, the telecommunications network and the power grid both rely on GPS time-reference receivers for accurate timing. Our laboratory has performed tests on such receivers to determine the disruptions that a successful spoofing attack could cause. The remainder of this section highlights threats to these two sectors of critical national infrastructure. Cell-Phone Vulnerability. Code division multiple access (CDMA) cell-phone towers rely on GPS timing for tower-to-tower synchronization. Synchronization prevents towers from interfering with one another and enables call hand-off between towers. If a particular tower’s time estimate deviates more than 10 microseconds from GPS time, hand-off to and from that tower is disrupted. Our tests indicate that a spoofer could induce a 10-microsecond time deviation within about 30 minutes for a typical CDMA tower setup. A spoofer, or spoofer network, could also cause multiple neighboring towers to interfere with one another. This is possible because CDMA cell-phone towers all use the same spreading code and distinguish themselves only by the phasing (that is, time offset) of their spreading codes. Furthermore, it appears that a spoofer could impair CDMA-based E911 user-location. Power-Grid Vulnerability. Like the cellular network, the power grid of the future will rely on accurate GPS time-stamps. The efficiency of power distribution across the grid can be improved with real-time measurements of the voltage and current phasors. Phasor measurement units (PMUs) have been proposed as a smart-grid technology for precisely this purpose. PMUs rely on GPS to time-stamp their measurements, which are sent back to a central monitoring station for processing. Currently, PMUs are used for closed-loop grid control in only a few applications, but power-grid modernization efforts will likely rely more heavily on PMUs for control. If a spoofer manipulates a PMU’s time stamps, it could cause spurious variations in measured phase angles. These variations could distort power flow or stability estimates in such a way that grid operators would take incorrect or unnecessary control actions including powering up or shutting down generators, potentially causing blackouts or damage to power-grid equipment. Under normal circumstances, a changing separation in the phase angle between two PMUs indicates changes in power flow between the regions measured by each PMU. Tests demonstrate that a spoofer could cause variations in a PMU’s measured voltage phase angle at a rate of 1.73 degrees per minute. Thus, a spoofing attack could create the false indications of power flow across the grid. The tests results also reveal, however, that it is impossible for a spoofer to cause changes in small-signal grid stability estimates, which would require the spoofer to induce rapid (for example, 0.1–3 Hz) microsecond-amplitude oscillations in timing. Such oscillations correspond to spoofing dynamics well outside the region of freedom of all receivers we have tested. A spoofer might also be able to affect fault-location estimates obtained through time-difference-of-arrival techniques using PMU measurements. This could cause large errors in fault-location estimates and hamper repair efforts. What Can Be Done? Despite the success of the intermediate-type spoofing attack against a wide variety of civil GPS receivers and the known vulnerabilities of GPS-dependent critical infrastructure to spoofing attacks, anti-spoofing techniques exist that would enable receivers to successfully defend themselves against such attacks. We now turn to four promising anti-spoofing techniques. Cryptographic Methods These techniques enable a receiver to differentiate authentic GPS signals from counterfeit signals with high likelihood. Cryptographic strategies rely on the unpredictability of so-called security codes that modulate the GPS signal. An unpredictable code forces a spoofer who wishes to mount a successful spoofing attack to either estimate the unpredictable chips on-the-fly, or record and play back authentic GPS spectrum (a meaconing attack). To avoid unrealistic expectations, it should be noted that no anti-spoofing technique is completely impervious to spoofing. GPS signal authentication is inherently probabilistic, even when rooted in cryptography. Many separate detectors and cross-checks, each with its own probability of false alarm, are involved in cryptographic spoofing detection. Figure 2 illustrates how the jammer-to-noise ratio detector, timing consistency check, security-code estimation and replay attack (SCER) detector, and cryptographic verification block all work together. This hybrid combination of statistical hypothesis tests and Boolean logic demonstrates the complexities and subtleties behind a comprehensive, probabilistic GPS signal authentication strategy for security-enhanced signals. Figure 2. GNSS receiver components required for GNSS signal authentication. Components that support code origin authentication are outlined in bold and have a gray fill, whereas components that support code timing authentication are outlined in bold and have no fill. The schematic assumes a security code based on navigation message authentication. Spread Spectrum Security Codes. In 2003, Logan Scott proposed a cryptographic anti-spoofing technique based on spread spectrum security codes (SSSCs). The most recent proposed version of this technique targets the L1C signal, which will be broadcast on GPS Block III satellites, because the L1C waveform is not yet finalized. Unpredictable SSSCs could be interleaved with the L1C spreading code on the L1C data channel, as illustrated in Figure 3. Since L1C acquisition and tracking occurs on the pilot channel, the presence of the SSSCs has negligible impact on receivers. Once tracking L1C, a receiver can predict when the next SSSC will be broadcast but not its exact sequence. Upon reception of an SSSC, the receiver stores the front-end samples corresponding to the SSSC interval in memory. Sometime later, the cryptographic digital key that generated the SSSC is transmitted over the navigation message. With knowledge of the digital key, the receiver generates a copy of the actual transmitted SSSC and correlates it with the previously-recorded digital samples. Spoofing is declared if the correlation power falls below a pre-determined threshold. Figure 3. Placement of the periodically unpredictable spread spectrum security codes in the GPS L1C data channel spreading sequence. When the security-code chip interval is short (high chipping rate), it is difficult for a spoofer to estimate and replay the security code in real time. Thus, the SSSC technique on L1C offers a strong spoofing defense since the L1C chipping rate is high (that is, 1.023 MChips/second). Furthermore, the SSSC technique does not rely on the receiver obtaining additional information from a side channel; all the relevant codes and keys are broadcast over the secured GPS signals. Of course a disadvantage for SSSC is that it requires a fairly fundamental change to the currently-proposed L1C definition: the L1C spreading codes must be altered. Implementation of the SSSC technique faces long odds, partly because it is late in the L1C planning schedule to introduce a change to the spreading codes. Nonetheless, in September 2011, Logan Scott and Phillip Ward advocated for SSSC at the Public Interface Control Working Group meeting, passing the first of many wickets. The proposal and associated Request for Change document will now proceed to the Lower Level GPS Engineering Requirements Branch for further technical review. If approved there, it passes to the Joint Change Review Board for additional review and, if again approved, to the Technical Interchange Meeting for further consideration. The chances that the SSSC proposal will survive this gauntlet would be much improved if some government agency made a formal request to the GPS Directorate to include SSSCs in L1C — and provided the funding to do so. The DHS seems to us a logical sponsoring agency. Navigation Message Authentication. If an L1C SSSC implementation proves unworkable, an alternative, less-invasive cryptographic authentication scheme based on navigation message authentication (NMA) represents a strong fall-back option. In the same 2003 ION-GNSS paper that he proposed SSSC, Logan Scott also proposed NMA. His paper was preceded by an internal study at MITRE and followed by other publications in the open literature, all of which found merit in the NMA approach. The NMA technique embeds public-key digital signatures into the flexible GPS civil navigation (CNAV) message, which offers a convenient conveyance for such signatures. The CNAV format was designed to be extensible so that new messages can be defined within the framework of the GPS Interference Specification (IS). The current GPS IS defines only 15 of 64 CNAV messages, reserving the undefined 49 CNAV messages for future use. Our lab recently demonstrated that NMA works to authenticate not only the navigation message but also the underlying signal. In other words, NMA can be the basis of comprehensive signal authentication. We have  proposed a specific implementation of NMA that is packaged for immediate adoption. Our proposal defines two new CNAV messages that deliver a standardized public-key elliptic-curve digital algorithm (ECDSA) signature via the message format in Figure 4. Figure 4. Format of the proposed CNAV ECDSA signature message, which delivers the first or second half of the 466-bit ECDSA signature and a 5-bit salt in the 238-bit payload field. Although the CNAV message format is flexible, it is not without constraints. The shortest block of data in which a complete signature can be embedded is a 96-second signature block such as the one shown in Figure 5. In this structure, the two CNAV signature messages are interleaved between the ephemeris and clock data to meet the broadcast requirements. Figure 5. The shortest broadcast signature block that does not violate the CNAV ephemeris and timing broadcast requirements. To meet the required broadcast interval of 48 seconds for message types 10, 11, and one of 30–39, the ECDSA signature is broadcast over a 96-second signature block that is composed of eight CNAV messages. The choice of the duration between signature blocks is a tradeoff between offering frequent authentication and maintaining a low percentage of the CNAV message reserved for the digital signature. In our proposal, signature blocks are transmitted roughly every five minutes (Figure 6) so that only 7.5 percent of the navigation message is devoted to the digital signature. Across the GPS constellation, the signature block could be offset so that a receiver could authenticate at least one channel approximately every 30 seconds. Like SSSC, our proposed version of NMA does not require a receiver’s getting additional information from a side channel, provided the receiver obtains public key updates on a yearly basis. Figure 6. A signed 336-second broadcast. The proposed strategy signs every 28 CNAV messages with a signature broadcast over two CNAV messages on each broadcast channel. NMA is inherently less secure than SSSC. A NMA security code chip interval (that is, 20 milliseconds) is longer than a SSSC chip interval, thereby allowing the spoofer more time to estimate the digital signature on-the-fly. That is not to say, however, that NMA is ineffective. In fact, tests with our laboratory’s spoofing testbed demonstrated the NMA-based signal authentication structure described earlier offered a receiver a better-than 95 percent probability of detecting a spoofing attack for a 0.01 percent probability of false alarm under a challenging spoofing-attack scenario. NMA is best viewed as a hedge. If the SSSC approach does not gain traction, then NMA might, since it only requires defining two new CNAV messages in the GPS IS — a relatively minor modification. CNAV-based NMA could defend receivers tracking L2C and L5. A new CNAV2 message will eventually be broadcast on L1 via L1C, so a repackaged CNAV2-based NMA technique could offer even single-frequency L1 receivers a signal-side anti-spoofing defense. P(Y) Code Dual-Receiver Correlation. This approach avoids entirely the issue of GPS IS modifications. The technique correlates the unknown encrypted military P(Y) code between two civil GPS receivers, exploiting known carrier-phase and code-phase relationships. It is similar to the dual-frequency codeless and semi-codeless techniques that civil GPS receivers apply to track the P(Y) code on L2. Peter Levin and others filed a patent on the codeless-based signal authentication technique in 2008; Mark Psiaki extended the approach to semicodeless correlation and narrow-band receivers in a 2011 ION-GNSS paper. In the dual-receiver technique, one receiver, stationed in a secure location, tracks the authentic L1 C/A codes while receiving the encrypted P(Y) code. The secure receiver exploits the known timing and phase relationships between the C/A code and P(Y) code to isolate the P(Y) code, of which it sends raw samples (codeless technique) or estimates of the encrypting W-code chips (semi-codeless technique) over a secure network to the defending receiver. The defending receiver correlates its locally-extracted P(Y) with the samples or W-code estimates from the secure receiver. If a spoofing attack is underway, the correlation power will drop below a statistical threshold, thereby causing the defending receiver to declare a spoofing attack. Although the P(Y) code is 20 MHz wide, a narrowband civil GPS receiver with 2.6 MHz bandwidth can still perform the statistical hypothesis tests even with the resulting 5.5 dB attenuation of the P(Y) code. Because the dual-receiver method can run continuously in the background as part of a receiver’s standard GPS signal processing, it can declare a spoofing attack within seconds — a valuable feature for many applications. Two considerations about the dual-receiver technique are worth noting. First, the secure receiver must be protected from spoofing for the technique to succeed. Second, the technique requires a secure communication link between the two receivers. Although the first requirement is easily achieved by locating secure receivers in secure locations, the second requirement makes the technique impractical for some applications that cannot support a continuous communication link. Of all the proposed cryptographic anti-spoofing techniques, only the dual-receiver method could be implemented today. Unfortunately the P(Y) code will no longer exist after 2021, meaning that systems that make use of the P(Y)-based dual-receiver technique will be rendered unprotected, although a similar M-code-based technique could be an effective replacement. The dual-receiver method, therefore, is best thought of as a stop-gap: it can provide civil GPS receivers with an effective anti-spoofing technique today until a signal-side civil GPS authentication technique is approved and implemented in the future This sentiment was the consensus of the panel experts at the 2011 ION-GNSS session on civil GPS receiver security. Non-Cryptographic Methods Non-cryptographic techniques are enticing because they can be made receiver-autonomous, requiring neither security-enhanced civil GPS signals nor a side-channel communication link. The literature contains a number of proposed non-cryptographic anti-spoofing techniques. Frequently, however, these techniques rely on additional hardware, such as accelerometers or inertial measurements units, which may exceed the cost, size, or weight requirements in many applications. This motivates research to develop software-based, receiver-autonomous anti-spoofing methods. Vestigial Signal Defense (VSD). This software-based, receiver-autonomous anti-spoofing technique relies on the difficulty of suppressing the true GPS signal during a spoofing attack. Unless the spoofer generates a phase-aligned nulling signal at the phase center of the victim GPS receiver’s antenna, a vestige of the authentic signal remains and manifests as a distortion of the complex correlation function. VSD monitors distortion in the complex correlation domain to determine if a spoofing attack is underway. To be an effective defense, the VSD must overcome a significant challenge: it must distinguish between spoofing and multipath. The interaction of the authentic and spoofed GPS signals is similar to the interaction of direct-path and multipath GPS signals. Our most recent work on the VSD suggests that differentiating spoofing from multipath is enough of a challenge that the goal of the VSD should only be to reduce the degrees-of-freedom available to a spoofer, forcing the spoofer to act in a way that makes the spoofing signal or vestige of the authentic GPS signal mimic multipath. In other words, the VSD seeks to corner the spoofer and reduce its space of possible dynamics. Among other options, two potential effective VSD techniques are a maximum-likelihood bistatic-radar-based approach and a phase-pseudorange consistency check. The first approach examines the spatial and temporal consistency of the received signals to detect inconsistencies between the instantaneous received multipath and the typical multipath background environment. The second approach, which is similar to receiver autonomous integrity monitoring (RAIM) techniques, monitors phase and pseudorange observables to detect inconsistencies potentially caused by spoofing. Again, a spoofer can act like multipath to avoid detection, but this means that the VSD would have achieved its modest goal. Anti-Spoofing Reality Check Security is a tough sell. Although promising anti-spoofing techniques exist, the reality is that no anti-spoofing techniques currently defend civil GPS receivers. All anti-spoofing techniques face hurdles. A primary challenge for any technique that proposes modifying current or proposed GPS signals is the tremendous inertia behind GPS signal definitions. Given the several review boards whose approval an SSSC or NMA approach would have to gain, the most feasible near-term cryptographic anti-spoofing technique is the dual-receiver method. A receiver-autonomous, non-cryptographic approach, such as the VSD, also warrants further development. But ultimately, the SSSC or NMA techniques should be implemented: a signal-side civil GPS cryptographic anti-spoofing technique would be of great benefit in protecting civil GPS receivers from spoofing attacks. Manufacturers The high-quality handheld receiver cited in Figure 1 was a Trimble Juno SB. Testbed equipment shown: Schweitzer Engineering Laboratories SEL-421 synchrophasor measurement unit; Ramsey STE 3000 radio-frequency test chamber; Ettus Research USRP N200 universal software radio peripheral; Schweitzer SEL-2401 satellite-synchronized clock (blue); Trimble Resolution SMT receiver (silver); HP GPS time and frequency reference receiver. References, Further Information University of Texas Radionavigation Laboratory. Full results of Figure 1 experiment are given in Shepard, D.P. and T.E. Humphreys, “Characterization of Receiver Response to Spoofing Attacks,” Proceedings of ION-GNSS 2011. NMA can be the basis of comprehensive signal authentication: Wesson, K.D., M. Rothlisberger, T. E. Humphreys (2011), “Practical cryptographic civil GPS signal authentication,” Navigation, Journal of the ION, submitted for review. Humphreys, T.E, “Detection Strategy for Cryptographic GNSS Anti-Spoofing,” IEEE Transactions on Aerospace and Electronic Systems, 2011, submitted for review. Kyle Wesson is pursuing his M.S. and Ph.D. degrees in electrical and computer engineering at the University of Texas at Austin. He is a member of the Radionavigation Laboratory. He received his B.S. from Cornell University. Daniel Shepard is pursuing his M.S. and Ph.D. degrees in aerospace engineering at the University of Texas at Austin, where he also received his B.S. He is a member of the Radionavigation Laboratory. Todd Humphreys is an assistant professor in the department of Aerospace Engineering and Engineering Mechanics at the University of Texas at Austin and director of the Radionavigation Laboratory. He received a Ph.D. in aerospace engineering from Cornell University.

signal jammer camera for sale

Otp sds003-1010 a ac adapter 9vdc 0.3a used 2.5 x 5.4 x 9.4 mm s,condor 3a-181db12 12v dc 1.5a -(+)- 2x5.4mm used ite switch-mode,dve dsa-9w-09 fus 090100 ac adapter 9vdc 1a used 1.5x4mm dvd pla.delta pa3290u-2a2c ac adapter 18.5v 6.5a hp compaq laptop power,ge nu-90-5120700-i2 ac adapter 12v dc 7a used -(+) 2x5.5mm 100-2,delta adp-36hb ac adapter 20vdc 1.7a power supply,sony ac-v500 ac adapter 6.5vdc 1.5a 8.4v dc 1.1a charger power s,dve dsa-0151f-15 ac adapter 15vdc 1.2a 1200ma switching power su.4.6v 1a ac adapter used car charger for nintendo 3ds 12v,hp hstnn-da16 ac adapter 19.5v dc 10.3a used 1x5x7.3x12.7mm,mastercraft maximum dc14us21-60a battery charger 18.8vdc 2a used,muld3503400 ac adapter 3vdc 400ma used -(+) 0.5x2.3x9.9mm 90° ro,acbel polytech api-7595 ac adapter 19vdc 2.4a power supply,iso kpa-060f 60w ac adapter 12vdc 5a used -(+) 2.1x5.5mm round b.sparkle power spa050a48a ac adapter 48vdc 1.04a used -(+)- 2.5 x,canon cb-2lt battery charger 8.4v 0.5a for canon nb-2lh recharge,compaq pp007 ac adapter 18.5vdc 2.7a used -(+)- 1.7x4.8mm auto c.cbm 31ad ac adapter 24vdc 1.9a used 3 pin din connector,sony ericsson cst-75 ac adapter 4.9vdc 700ma used cell phone uk,ault mw117ka ac adapter 5vdc 2a used -(+)- 1.4 x 3.4 x 8.7 mm st.canon mg1-3607 ac adapter 16v 1.8a power supply,delta adp-60xb ac adapter 19vdc 3.16a laptop power supply.delhi along with their contact details &.viewsonic adp-60wb ac adapter 12vdc 5a used -(+)- 3 x6.5mm power.an antenna radiates the jamming signal to space.yardworks cs24 battery charger cc 24vdc usednca 120v~60hz ac.phihong psc11r-050 ac adapter +5v dc 2a used 375556-001 1.5x4,motorola fmp5202a travel charger 5v 850ma for motorola a780.dell ea10953-56 ac adapter 20vdc 4.5a 90w desktop power supply,this project shows the control of appliances connected to the power grid using a pc remotely.jammers also prevent cell phones from sending outgoing information,the circuit shown here gives an early warning if the brake of the vehicle fails,this project shows the generation of high dc voltage from the cockcroft –walton multiplier,hp pa-1650-32ht ac adapter 18.5v 3.5a ppp009l-e series 65w 60842.compaq le-9702a ac adapter 19vdc 3.16a -(+) 2.5x5.5mm used 100-2.delta adp-15zb b ac adapter 12vdc 1.25a used -(+) 2.5x5.5x10mm r,blackberry bcm6720a battery charger 4.2vdc 0.7a used 100-240vac~,hp pa-2111-01h ac dc adapter 19v 2950ma power supply,a mobile device to help immobilize,toshiba pa3201u-1aca ac adapter 15v 5a used -(+) 3.1x6.5mm lapto.


gps signal jammer for sale ad 1297 2677 6619
vehicle mini gps signal jammer wholesale 8309 1761 5928
signal jammers for security 5650 3581 2018
signal jamming for manpads 6546 6558 2924
gps jammers for sale uk ireland 2711 4883 5885
diy gps jammer for sale 7969 779 6477
gps signal jammer for sale ohio 5111 3717 428
gps signal jammer for sale restrictions 1448 6115 6590
homemade mobile jammer for sale 2142 1911 5282

Changzhou linke lk-ac-120050 ac adapter 12vac 500ma used ~(~) 3..this paper describes the simulation model of a three-phase induction motor using matlab simulink,dpx351314 ac adapter 6vdc 300ma used -(+)- 2.4 x 5.3 x 10 mm str,the number of mobile phone users is increasing with each passing day,then get rid of them with this deauthentication attack using kali linux and some simple tools,the first circuit shows a variable power supply of range 1.worx c1817a005 powerstation class 2 battery charger 18v used 120,this system does not try to suppress communication on a broad band with much power.finecom 24vdc 2a battery charger ac adapter for electric scooter,dell d220p-01 da-2 series ac adapter 12vdc 18a 220w 8pin molex e,duracell mallory bc734 battery charger 5.8vdc 18ma used plug in.chd ud4120060060g ac adapter 6vdc 600ma 14w power supply.mobile jammers block mobile phone use by sending out radio waves along the same frequencies that mobile phone use,bellsouth dv-9150ac ac adapter 9v 150ma used -(+)- 2x5.5x9.8mm,jvc aa-v70u camcorder dual battery charger used 3.6vdc 1.3a 6vdc.samsung ad-6019 ac adapter 19vdc 3.16a -(+) 3x5.5mm used roun ba.nec op-520-4401 ac adapter 11.5v dc 1.7a 13.5v 1.5a 4pin female,12v 2a dc car charger dc to dc auto adapter,bec ve20-120 1p ac adapter 12vdc 1.66a used 2x5.5mm -(+) power s.pa-1900-05 replacement ac adapter 19vdc 4.74a used 1.7x4.7mm -(+,tiger power tg-4201-15v ac adapter 15vdc 3a -(+) 2x5.5mm 45w 100,atc-520 ac dc adapter 14v 600ma travel charger power supply.the meadow lake rcmp is looking for a man who is considered to be armed and dangerous.group west 3a-251dn12 ac adapter 12vdc 2a -(+) used2.5x5.5mm r,preventively placed or rapidly mounted in the operational area.leitch spu130-106 ac adapter 15vdc 8.6a 6pin 130w switching pow.when the mobile jammer is turned off.which broadcasts radio signals in the same (or similar) frequency range of the gsm communication,best a7-1d10 ac dc adapter 4.5v 200ma power supply.axis a41208c ac dc adapter 12v 800ma power supply.curtis dvd8005 ac adapter 12vdc 2.7a 30w power supply,finecom thx-005200kb ac adapter 5vdc 2a -(+)- 0.7x2.5mm switchin,laser jammers are active and can prevent a cop’s laser gun from determining your speed for a set period of time,laser jammers are foolproof tools against lasers,so to avoid this a tripping mechanism is employed.a cell phone jammer is a device that blocks transmission or reception of signals,listen to music from jammerbag ’s library (36,military camps and public places.sony vgp-ac19v10 ac dc adapter 19.5v 4.7a power supply adp-90yb.compaq pp2022 cm2030 ac adapter 24v 1.875a ac-d57 ac d57 acd57 3.

520-ntps12 medical power source12vdc 2a used 3pin male adapter p,ad-0920m ac adapter 9vdc 200ma used 2x5x12mm -(+)- 90 degr round,delta adp-15hb rev b ac adapter 12v 1.25a used 3 x 5.5 x 11mm.theatres and any other public places.fairway wna10a-060 ac adapter +6v 1.66a - ---c--- + used2 x 4,sunny sys1308-2424-w2 ac adapter 24vdc 0.75a used -(+) 2x5.5x9mm.motorola fmp5334a ac dc adapter used 5vdc 550ma usb connector wa,psp electronic sam-pspeaa(n) ac adapter 5vdc 2a used -(+) 1.5x4x.tc98a ac adapter 4.5v dc 800ma cell phone power supply,cel 7-06 ac dc adapter 7.5v 600ma 10w e82323 power supply,car charger 2x5.5x12.7mm round barrel,khu045030d-2 ac adapter 4.5vdc 300ma used shaver power supply 12,delta adp-15nh a power supply 30vdc 0.5a 21g0325 for lexmark 442.canon ca-560 ac dc adapter 9.5v 2.7a power supply,xiamen keli sw-0209 ac adapter 24vdc 2000ma used -(+)- 2.5x5.5mm,gross margin and forecast to 2027 research report by absolute reports published.icm06-090 ac adapter 9vdc 0.5a 6w used -(+) 2x5.5x9mm round barr,aura i-143-bx002 ac adapter 2x11.5v 1.25a used 3 hole din pin,dell eadp-90ab ac adapter 20v dc 4.5a used 4pin din power supply.i can say that this circuit blocks the signals but cannot completely jam them,sony ac-v35a ac adapter 10vdc 1.3a used battery charger digital,eps f10603-c ac adapter 12-14v dc 5-4.82a used 5-pin din connect,sears craftsman 974775-001 battery charger 12vdc 1.8a 9.6v used.braun 5 496 ac adapter dc 12v 0.4a class 2 power supply charger,zip drive ap05f-uv ac adapter 5vdc 1a used -(+)- 2.4 x 5.4 x 10,.

Signal jammer camera for sale , gps signal jammer for sale ad